The device is calibrated to ISO 11943. It calculates and displays results according to ISO 4406:99, SAE AS 4059, NAS 1638 und GOST 17216.
Voltage
9-33 V dc
Operating Pressure
Up to 6,090 psi (420 bar) dynamic
protection Class
IP67
Flow Rate
50-400 ml/min (required for operation)
Fluid Connection
M16 x 2.0 (Minimess®)
Electric Connection
M12 x 1 (8 pole)
Data Memory
On-board 4MB storage capacity
Fluid Compatibility
Mineral oils, phosphate esters and specified synthetics (Skydrol by special option only). Not for use with water glycol or other water based fluids. Water levels above saturation in any fluids will cause the PM-1 to malfunction.
Temperature Range
Oil
14°F to 176°F
(-10°C to 80°C)
Air
14°F to 176°F
(-10°C to 80°C)
Storage
-4°F to 176°F
(-20°C to 80°C)
interface
RS-232, analog output 4-20 mA configurable, digital alarm output, digital input to start and stop readings
Ordering Inforamation
PM-1
PM-1 Particle Monitor
PM-1-PWRSUP-60
PM-1 electrical power supply for portable use (120V AC, 1P, 60 Hz to 24 V dc)
For PM-1portable counting you must purchase the PM-1-DAT AND either the PM-1-PWRSUP-60 (for 60 Hz) or the PM-1-PWRSUP-50 (50 Hz) to power the unit. The unit cannot be powered with just the PM-1-PWRSUP-60 or -50. The PM-1-DAT allows for connection to RS232 data port for data acquisition and download.
PM-1-PWRSUP-50
PM-1 electrical power supply for portable use (220V AC, 1P, 50 Hz to 24 V dc)
For PM-1portable counting you must purchase the PM-1-DAT AND either the PM-1-PWRSUP-60 (for 60 Hz) or the PM-1-PWRSUP-50 (50 Hz) to power the unit. The unit cannot be powered with just the PM-1-PWRSUP-60 or -50. The PM-1-DAT allows for connection to RS232 data port for data acquisition and download.
PM-1-PWRCAB
PM-1 9-33 V power cable with M-12 x 1 (8 pole) connection 15’ (5 m) power cable plus 1 x 8 pole connection for PM-1
PM-1-HKIT-60
Portability kit for PM-1. Includes: Pelican™ case, sampling hoses for high pressure Minimess® & low pressure lube application adapters, outlet line flow control attachment, PM-1-PWRSUP-60 power supply (60 Hz) and PM-1-DAT data/power adapter.
PM-1-HKIT-50
Portability kit for PM-1. Includes: Pelican™ case, sampling hoses for high pressure Minimess® & low pressure lube application adapters, outlet line flow control attachment, PM-1-PWRSUP-50 power supply (50 Hz) and PM-1-DAT data/power adapter.
PM-1-BR
PM-1 back mounting bracket with rubber vibration suppression
PM-1-USB
USB adapter – RS-232 serial
PM-1-DAT
15’ (5 m) data cable with open ends
For PM-1portable counting you must purchase the PM-1-DAT AND either the PM-1-PWRSUP-60 (for 60 Hz) or the PM-1-PWRSUP-50 (50 Hz) to power the unit. The unit cannot be powered with just the PM-1-PWRSUP-60 or -50. The PM-1-DAT allows for connection to RS232 data port for data acquisition and download.
PM-1-FITLOW
Low pressure lube system fittings to replace standard Minimess® inlet & outlet connections.2 Suitable for low pressure systems< 29 psi (2 bar) where achieving minimum flow index 50,000 reading (50 ml/min) is not possible.
PM-1-SC
PM-1 Soft Calibration
It is recommended that the unit receives a soft calibration every 2 years of service to ensure the unit is still operating as intended. If soft calibration indicates the unit is not functioning properly, a hard calibration should be performed.
PM-1-HC
PM-1 Hard Calibration
It is recommended that the unit receives a soft calibration every 2 years of service to ensure the unit is still operating as intended. If soft calibration indicates the unit is not functioning properly, a hard calibration should be performed.
